This Website

We've encountered this article relating to How to Install a Bathtub listed below on the internet and accepted it made sense to discuss it with you on this page.

Mounting a tub isn't specifically brain surgery, yet it does call for solid plumbing, woodworking, and occasionally, tiling skills. Changing an old bath tub with a new one is likewise a reasonably challenging task. If the old bathtub is readily easily accessible, the job can relocate rapidly; if you have to open up a wall surface to remove the old bathtub as well as place the brand-new bath tub, the job is a lot harder. In either case, the task is within a house handyman's abilities, although you will require a helper to vacate the old tub and set in the new one. Ensure you have actually qualified on your own for the task and are comfortable attempting it. As opposed to employing a professional to take over a halfway-completed job, it is much better to consider using one before you begin. Opportunities are you might require a specialist plumber to make tube connections.
This write-up will certainly aid you mount a brand-new tub in your restroom if you have currently acquired a new tub and also don't need to alter the plan of your previous water pipelines.
Your tools and also material checklist should comprise the following:

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Tape Measure


• Pipeline Caps


 

Removing Old Taps

If you require to replace old faucets with new ones as a part of your installment, then the first thing you must do is disconnect the water system. After doing so, turn on the taps to drain pipes any kind of water staying in the system. The process of eliminating the existing taps can be quite troublesome because of the limited access that is typically the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel prepared for the staying water that will come from the pipelines. As soon as the supply pipes have actually been gotten rid of, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary faucets from transforming throughout this procedure. When the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Prior to proceeding to fit the new faucets, compare the pipe links on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.

Suitable New Taps

If the tails of the new faucets are plastic, after that you will need a plastic port to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet and the various other end provides a link to the existing supply pipelines.
If you require to fit a monobloc, then you will certainly call for lowering couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the installing opening in the bath/basin making certain that the washing machines remain in area between the faucet as well as the sink. Safeguard the tap in position with the manufacturer given backnut. When the faucet is securely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal tap adapters. The former type must be linked to the tap ends first, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.

Setting up the Tub

Using both wooden boards under its feet, position the bathtub in the required setting. The wood boards are useful in uniformly spreading the weight of the bath tub over the location of the boards instead of focusing all the weight onto four small factors.
The next goal is to guarantee that the bath tub is leveled all round. This can be attained by inspecting the spirit level and also adjusting the feet on the bathtub till the spirit level reviews level.
To install faucets, fit all-time low of the furthest versatile tap connector to the appropriate supply pipe by making a compression sign up with; then do the very same for the other faucet.
Switch on the water supply and also check all joints and new pipework for leakages as well as tighten them if required. Fill the bathtub and also inspect the overflow electrical outlet and the regular electrical outlet for leakages.
Ultimately, fix the bath paneling as defined in the producer's instruction manual. Tiling and sealing around the bathtub ought to wait until the tub has actually been made use of at least once as this will settle it into its final position.

Preparing for the Installment

Firstly, the supporting framework supplied with the bath must be fitted (if required) according to the manufacturer's directions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is important to make certain that if the faucet features a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the faucets system to prevent stress on the bath tub.
Fit the versatile tap adapters to the bottom of the two faucets making use of 2 nuts and also olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you utilize every one of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom should currently be ready to be suited its last placement.

Tiling Around the Bathtub

In the area where the bathroom meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the installation can move enough to fracture a rigid seal, creating the water to permeate the wall surface between the bathroom and also the tiling, leading to issues with dampness as well as possible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to blend in your components and also fittings. They are marketed in tubes as well as cartridges, as well as can sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to always load the tub with water prior to sealing, to enable the activity experienced when the bathtub is in use. The sealer can fracture rather early if you do not think about this activity before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally conveniently readily available on the marketplace. It is advisable to fit the floor tiles making use of water-resistant or water-proof adhesive as well as cement.

A Step-by-Step Guide to Installing a Bathtub

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

 

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

 

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

Remove the Existing Bathtub

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

 

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

Choose the Right Bathtub

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

Install the Plumbing and Ledger Board

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

 

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

Install the Bathtub

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

 

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

 

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

Hook up the Plumbing

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

Install the Bathtub Surround

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

 

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

 

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

 

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

I'm certainly very involved in Tools You Need to Install a New Bathtub and I hope you enjoyed reading our post. Loved our article? Please share it. Let someone else check it out. I enjoy reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.

24/7 support? Call.